Operating Guide for 50VS69A. 55VS69A and .. Your Hitachi LCD Rear Projection Television has an internal lamp that lights up the TV screen. owner’s manual of each component for the location of video and audio inputs and outputs . Download Service Manual Hitachi 50vs69a Pdf. 2 safety points you should know about your hitachi lcd rear projection television our reputation has been built on. Sat, 08 Dec GMT service manual hitachi 50vs69a pdf – This. HITACHI Service Manual is intended for the qualified service personnel and it.
|Published (Last):||21 February 2008|
|PDF File Size:||7.20 Mb|
|ePub File Size:||15.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
Do not use an module. If they are not shiny, reheat them oblong through which the IC leads are inserted and then bent flat and, if necessary, apply additional solder. Critical Copper Pattern requires special soldering techniques to ensure the maintenance of reliability and safety standards, contact Trace along the copper pattern from both wire sides of the pat- your Hitachi personnel.
These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose. LC67 Information for service about lead-free solder Introduction Hitachi introduced lead-free solder to conserve the “Earth Environment”.
Please refer to the following before servicing. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America ,Ltd.
The differences between each set are shown below. Component Video Luminance Y Apply mark on body LC67 Display Specifications 7.
LC67 Display Specifications cont Monitor out Set the Monitor out: However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. For best performance, video cables should use Ohm coaxial shielded wire.
Please make sure the Blue Power light indicator is not lit OFF when you are not watching for long lasting performance. Front Control Panel Connections Note: Special device cables will be required according to the device specifications. This card slot is for future software upgrades.
In order to receive written This slot is for the CableCARD that will be provided by your local cable operator to gain access to chosen cable channels. Use these connections in place of the standard video connection if your device has this feature. Using other lamps may cause damage to the TV Set. For lamp recycling and disposal information, go to www.
For product recycling and disposal information, contact your local government agency or the Electronic Industries Alliance at www. Remove the lamp unit by holding the lamp handlethen pulling outwards. The lamp is very hot and may cause fire or severe burns. For product recycling and disposal information, contact your local government agency or eRecycle. NTSC i signal generator.
Use any Hitachi remote control when making an 4 Check the following process for initialization opera- adjustment. Heat run should be performed with moving picture or no signal. If and only if the customer request to change the color uniformity, follow the instruction below. Checking Check that the data is normal. B has five LED on board. It may take a few seconds for the sequence. After Program is loaded without error, all LED will be turned off.
Waveforms taken using a Color Bar signal with H sync 31 khz and V. Voltage Symbol Pin No.
Hitachi 50VS69A Manuals
Components marked with a! Don’t degrade the safety of hittachi receiver through improper servicing. Components marked with a have special characteristics important to safety.
Page of Go. Table of Contents Add to my manuals Add. Hitachi 51F59 Operating Manual 75 pages. Table Of Contents No. Page 7 Critical Copper Pattern requires special soldering techniques to ensure the maintenance of reliability and hitafhi standards, contact Trace along the copper pattern from both wire sides of the pat- your Hitachi 50vss69a. Page 9 LC67 Information for service about lead-free solder Introduction Hitachi introduced lead-free solder to conserve the “Earth Environment”.
Agency Regulatory Information Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America ,Ltd. Page 18 LC67 Display Specifications cont Page 19 LC67 Display Specifications cont Page 20 LC67 Display Specifications cont Page 21 LC67 Display Specifications cont Page 22 LC67 Display Specifications cont Page 23 LC67 Display Specifications cont Page 24 LC67 Display Specifications cont Page 25 LC67 Display Specifications cont Page 30 LAMP 3.
Composite Video This card slot is for future software upgrades. Page 37 For lamp recycling and disposal information, go to www. Page 39 For lamp recycling and disposal information, go to www.
HITACHI 50VS69A SERVICE MANUAL Pdf Download.
Adjustments NTSC i signal generator. Drive Adjustment Check LC67 2. This manual also for: Comments to this Manuals Your Name.
Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again.
Got it, continue to print. Don’t have an account?